Adsorption compressed air desiccants

“AGS Engineering” designs and manufactures adsorption compressed air desiccants using short-cycle adsorption technology.
Производительность до 200 m3/min
Dew point from -20 to -70
1
The principle of operation of the adsorption desiccant
The principle of operation of the adsorption desiccant is based on the absorption of moisture vapor by the solid surface of the adsorbent (active aluminum oxide): The source air from the compressor is supplied to the dryer through a filter (F-1 and F-2), which cleans it of oil and drip moisture. Next, air enters the column "A", where moisture is absorbed using a layer of active alumina, and then through the dust filter (F-3) to the consumer. During the drying stage in the column "A", the process of absorption of moisture occurs, and in the column "B" - the regeneration stage. “Cold” regeneration - The adsorption process is an equilibrium process in which the adsorption time is equal to the desorption time.
The principle of operation of the adsorption desiccant is based on the absorption of moisture vapor by the solid surface of the adsorbent (active aluminum oxide): The source air from the compressor is supplied to the dryer through a filter (F-1 and F-2), which cleans it of oil and drip moisture. Next, air enters the column "A", where moisture is absorbed using a layer of active alumina, and then through the dust filter (F-3) to the consumer. During the drying stage in the column "A", the process of absorption of moisture occurs, and in the column "B" - the regeneration stage. “Cold” regeneration - The adsorption process is an equilibrium process in which the adsorption time is equal to the desorption time.
1
What a desiccant consists of
AGS adsorption desiccants can operate with minimal loss of compressed air for regeneration.
1
1. Highly efficient adsorbent In our generators we use only high-quality and proven adsorbents.
2. Two types of regeneration GA series dehumidifiers can be supplied with two regeneration methods: Cold and Hot Vacuum.
3. Built-in filters All dehumidifiers are supplied with filters installed at the inlet and outlet.
4. Dew Point Sensor At the outlet of the dryer, a dew point converter is installed to control the cycles when the adsorbent is saturated.
5. Adsorbers Made of aluminum pipe with a polished surface and air distribution devices over the cross section.
6. Pneumatic valves Pneumatic piping is designed for 2 million cycles of unloading load.
Adsorber design

has a device for distributing compressed air over the cross section of the adsorption layer at the inlet and outlet. Also, filter elements are installed inside the adsorber that trap adsorption dust to prevent abrasion of valve seals. The adsorbers have service fittings for servicing and replacing the molecular sieve.

Advantages In the GA series adsorption desiccants, only high-quality European components with extended service life and increased reliability are used
1
Service life >5 years In our dehumidifiers, we use only high-quality and proven CarboTech adsorbents.
1
Dew point sensor An integrated dew point sensor allows you to control adsorption cycles in a more economical mode.
1
Valve Harness The valve strapping is implemented on the basis of pneumatic valves SMC and FESTO, designed for 2 million cycles of operation.
1
Modular design The dehumidifiers are compact in size and modular in design, so commissioning will take no more than two hours.
1
Adaptive management The intelligent control system allows significant savings in compressed air for regeneration.
The lineup
GA Series Desiccants Available in Various Modifications
1
GA - 2
Series: GA 5..84 (0,1-6 m3/min), cold regeneration
Download a brochure
1
GA - 35
Series: GA 5..84 (0,1-6 m3/min), cold regeneration
Download a brochure
1
GA - 170
Series: GA 100-1500 (6-95 m3/min), cold regeneration
Download a brochure
Submit your inquiry
If you are interested in our equipment and you want to receive detailed information
Order a call back
Order a business proposal